PBR – Wall Panels

Home/Products/Wall Panels/PBR Wall Panels

The PBR panel’s deep ribs create an even-shadowed appearance. The area between the major ribs is reinforced with minor ribs. PBR is one of the most economical panel systems and can be used for both roof and wall applications.

Gauge

  • 26 gauge (standard)
  • 24 gauge
  • 22 gauge

Length

  • 45′ maximum length is standard but longer lengths are available by special request

Dimensions

  • 36″ by 1 1/4″

Finish

  • Galvalume Plus®
  • Signature® 200 Colors
  • Signature® 300 Colors

NOTE: Oil-canning is not considered grounds for rejection of any panel system. Oil-canning can occur in any panel with wide flat sections. Heavier gauge, embossing, striations, flatter sub-frame systems and support from a solid sub-deck can all help to minimize oil-canning.

Fasteners

  • Standard coated, zinc- aluminum cast head, or stainless steel head screw

Usage

  • Roof, wall, liner, mansard, and soffit
    panel applications

Limitations

  • Not designed for coverage over bar joist or to be used as rigid secondary; Five foot on center purlin spacing

Attributes

  1. Reverse rolled profile
  2. Purlin bearing leg
  3. Installation may start at either end
  4. Economical profile
  5. 36″ coverage
  6. Wind uplift rating
  7. Diaphragm action
  8. Light transmitting panels
  9. Finish warranty

Advantages

  1. The panel can serve as an alternate wall panel by putting the paint finish on the under side
  2. An additional leg is rolled on one side of lap rib to facilitate installation
  3. Flexible installation
  4. Cost effective
  5. Ease of installation
  6. The panel qualifies for UL® 90 in multiple construction numbers
  7. The panel configuration enhances diaphragm capabilities for purlin stability
  8. Profile light transmitting panels are available for the PBR panel
  9. Used with long-life fasteners this panel has a 25-year warranty

PBR Wall – Section Properties

Properties Notes:

  1. All calculations for the properties of PBR panels are calculated in accordance with the 2001 edition of the North American Specification For Design Of Cold-Formed Steel Structural Members.
  2. Ixe is for deflection determination.
  3. Sxe is for bending.
  4. Maxo is allowable bending moment.
  5. All values are for one foot of panel width.

Allowable Uniform Loads 
In Pounds Per Square Foot

Allowable Uniform Loads Notes:

    1. Strength calculations based on the 2007 AISI Standard “North American Specification for the Design of Cold-formed Steel Structural Members”, with 2009 and 2010 Supplements.
    2. Allowable loads are applicable for uniform loading and spans without overhangs.
    3. Gravity/Pressure load capacities are for those loads that push the panel against its supports. The applicable limit states are flexure, shear, combined shear and flexure, web crippling at end and interior supports, and a deflection limit of L/180 under strength-level loads.
    4. Wind Suction load capacities are for those loads that pull the panel away from its supports. The applicable limit states are flexure, shear, combined shear and flexure, and a deflection limit of L/60 under 10-year wind loading.
    5. Panel pullover and Screw pullout capacity must be checked separately using the screws employed for each particular application when utilizing this load chart.
    6. Effective yield strength has been determined in accordance with section A2.3.2 of the 2007 NAS specification.

     

    The engineering data contained herein is for the expressed use of customers and design professionals. Along with this data, it is recommended that the design professional have a copy of the most current version of the North American Specification for the Design of Cold-Formed Steel Structural Members published by the American Iron and Steel Institute to facilitate design. This specification contains the design criteria for cold-formed steel components. Along with the specification, the designer should reference the most current building code applicable to the project jobsite in order to determine environmental loads. If fur ther information or guidance regarding cold-formed design practices is desired, please contact the manufacturer.

    EFFECTIVE NOVEMBER 3, 2004
    SUBJECT TO CHANGE WITHOUT NOTICE

    Galvalume Plus® is a registered trademark of BIEC International, Inc.
    Signature® is a registered trademark of the NCI Group.